|
|
|
Step 1 - The Spitzlift is folded up for
convenient and compact storage.
Step 2 - The strap is
unloosened and the two pins removed to begin the easy set up.
Step 3 - The cross member is set with two
pins and the lift is now ready to lift 700 lbs!. |
 |
|
The Truck Receiver
(ktur-364) or VAN/SUV Receiver (ksvr-224) Kits |
|
The Truck Receiver
Mounting Kit in action ... |
 |
 |
 |
 |
|
The Truck Receiver Kit can be used to
mount the Spitzlift on either side of the rear of your truck. |
 |
 |
 |
 |
|
The Truck Receiver Kit can be used to
mount the Spitzlift on a Utility Vehicle. |
Lifting a barrel into the pickup. |
|
The Van/SUV Receiver
Mounting Kit in action ... |
 |
 |
 |
 |
|
Set up on
Service Van |
Set up on a
SUV |
Lifting an Air Compressor |
Set up on a
Delivery Van |
|
The Truck Receiver
& Van/SUV Mounting Kits fit standard 2" hitch receivers. |
|
Step 1 - Insert the receiver arm into the
receiver hitch on vehicle and install hitch pin.
Step 2 - Insert post holder base into the
receiver arm.
Step 3 - Release the pin
in the support leg, level the receiver arm, and insert pin back into the
support leg to lock in place, to prevent rocking. |
 |
|
The Surface
Mounting Kit |
|
|
|
The Surface Mounting Kit
in action ... |
 |
 |
 |
 |
|
Lifting a
valve |
Mounted in
Pick Up Truck |
Mounted in
Pick Up Truck |
Lifting a
Tractor Tire |
 |
|
|
|
|
Lifting a
Snake |
|
|
|
|
The Surface Mounting Kit
enables the Spitzlift to be mounted on just about any vehicle (flatbed
trucks, sprinter vans, pickups)! It is designed to bolt through the bed
of the vehicle to the vehicle's frame. ... |
|
Step 1 - The surface mount is installed
in the bed of this pickup.
Step 2 - The universal post holster base
is inserted into the open channel of the surface mount.
Step 3 - The lift is then
inserted into the holster base and ready for lifting. |
Step 1 |
Step 2 |
Step 3 |
|
The Surface Mount Kit is
installed in a Sprinter Van. |
 |
 |
 |
|
|
Step 1 & 2 |
Step 3 |
Lifting a tool cart into a Sprinter Van. |
|
|
 |
 |
|
|
The
Corner Mounting Kit |
|
|
|
The Corner Mounting Kit is a
universal mounting adapter, made ideally for utility bed type
vehicles, but will allow you to mount the Spitzlift anywhere there
is a corner - i.e. flatbed trailer, utility trailer, loading dock,
etc. The Corner Mounting Kit in
action ... |
|
|
 |
Step 1 - The corner unit is being mounted
on the corner of this utility bed pickup.
Step 2 - The lift is then
inserted into the corner unit and ready for lifting. |
 |
 |
 |
 |
|
Mounted in a
Utility Bed |
Lifting a
Sand Blaster Unit |
Lifting an
Electric Motor |
Lifting a
Tamper |
|
The Bolt
On Weld On Kit |
|
|
|
The Bolt On/Weld On Kit
allows the Spitzlift to be mounted virtually any where! This unit
can be mounted onto just about anything that has the structural
integrity to support the load you are lifting. |
 |
 |
 |
 |
|
Mounted on a
Flat Bed Truck. |
On side of a
flatbed truck |
On a covered
truck |
On a flatbed
trailer |
|
Step 1 - Mount the Bolt On / Weld On
adapter to the location you want.
Step 2 - Insert post holder base into the
Bolt On/Weld On adapter.
Step 3 - Insert the
Spitzlift into the post holster base. |
 |
 |
 |
|
|
Step 1 |
Step 2 |
Step 3 |
|
|
 |
 |
 |
|
The Universal Base |
|
|
|
The Universal Base Kit
can be installed in most pickups in about 30 minutes - and the universal
base adjusts to fit most trucks and trailers. It extends no further than
the wheel well on the side of your pickup - allowing you to still haul
at full capacity.
The Universal Base Kit in
action ... |
 |
 |
 |
 |
|
Lifting a
Lawn Mower |
Lifting a
Boat Motor |
Lifting a
Generator |
Lifting a
Tree |
 |
|
|
|
|
Lifting a
barrel |
|
|
|
|
Bolt On Post Mount |
|
|
The Bolt On Post Mount Kit
allows the Spitzlift to be mounted virtually any where! This unit
can be mounted onto just about anything that has the structural
integrity to support the load you are lifting.
The Bolt On Post Mount Kit in
action ... |
|
Step 1 - Mount the Bolt On Post Mount
adapter to the location you want.
Step 2 - Insert the Spitzlift into the
Bolt On Post Mount adapter.
Step 3 - Start lifting! |
 |
 |
|
|
|
Step 1 |
Step 2 |
Step 3 |
|
Military Applications |
|
|
|
Military
Spitzlift Applications - our experienced engineering and design team is
able to quickly adapt to different applications, while maintaining
light-weight portability and quick assembly.
|
 |
 |
 |
 |
| Military
Use |
Military
Use |
Military
Use |
Military
Use |
 |
 |
 |
 |
|
Off the deck
of Sea Launch |
Coast Guard Cutter |
Coast Guard Cutter |
On a Submarine |
|
The Wall Saddle
Mount |
|
|
|
The Wall
Saddle Mount is designed
for mounting the Spitzlift on a
concrete, steel reinforced, parapet wall. |
 |
 |
 |
 |
|
Step 1 - Place the wall saddle mount post
base to the wall and tighten. |
Step 2 - Place the stabilizer bar into
saddle mount post base. |
Step 3 - Place the other saddle mount
over the wall and insert stabilizer bar and tighten to wall. |
Step 4 - Place the Spitzlift into the
base and secure the safety cable. |
|
The Wall Saddle Mount
in action ... |
 |
 |
 |
 |
|
Package Unit |
Package Unit |
Package Unit |
Package Unit |
